Central Vacuum System Pressure Loss: Sizing the Main Line

Pressure loss in a central vacuum system usually shows up after commissioning: the gauge at the pump reads 400 mbar while station eight runs at 340 mbar, and suction cups start slipping. The pump was chosen correctly; the piping took the difference. Using an eight-station line as the example, this note walks through the duty list, total flow, main line size, branch size, buffer tank and machine selection in sequence.

1. Duty list: what each station needs

The first sheet in a central vacuum project is not a pump datasheet, it is a station list.

StationDutyWorking vacuumPeak flow (at inlet)Cycle
1–6Cup handling, fixture clamping400 mbar abs40 m³/h each4 s pump, 1 s release
7–8Packaging chamber evacuation100 mbar abs40 m³/h each12 s

Flow is stated at the inlet condition: what the pump displaces per hour at 400 mbar, not the atmospheric equivalent. 40 m³/h at 400 mbar equals 15.8 m³/h at atmosphere. The two figures differ by 2.5 times, and pipe diameter must follow the first one.

2. From station flow to main line flow

All eight stations running at once demand 6 × 40 + 2 × 40 = 320 m³/h. Stations normally alternate, so with a simultaneity factor of 0.6 the average system flow is 192 m³/h. The pump is sized on average flow, peaks are covered by the buffer tank and a standby machine — the usual approach for central vacuum, described in multi-station central vacuum.

The 0.6 factor is an assumption, not a constant. Where all stations are triggered by one signal and move in sync, use 1.0, size the pump for 320 m³/h and go one nominal size larger on the main line.

3. Main line size: vacuum pipe sizing and velocity

Assume a 30 m main with six 90° elbows and two ball valves, carrying 300 m³/h at 400 mbar, dry air at 20 °C, density 0.475 kg/m³ (39% of the atmospheric 1.204 kg/m³). Pressure drop follows Darcy-Weisbach with the Blasius friction factor; elbows count as 20 diameters of equivalent length, ball valves as 3.

Nominal sizeBoreVelocityReynolds numberPressure dropShare of 400 mbar
DN5044 mm54.8 m/s6.3×10⁴115 mbar28.8%
DN6559 mm30.5 m/s4.7×10⁴30 mbar7.5%
DN8074 mm19.4 m/s3.8×10⁴10.8 mbar2.7%
DN10094 mm12.0 m/s3.0×10⁴3.7 mbar0.9%

Keeping the main line loss within 5% of working pressure is the common target. DN50 is out: 115 mbar over 30 m leaves the far end below 300 mbar. DN65 at 30 mbar (7.5%) is tight. DN80 lands at 10.8 mbar (2.7%), leaving 389 mbar at the last station.

The velocity column tells the same story: DN80 runs 19.4 m/s, inside the usual 15–30 m/s band for mains, while DN50 at 54.8 m/s brings noise, elbow erosion and particle entrainment.

4. Branch lines and valves

A correct main can still be ruined at the branch. One station at 40 m³/h, branch 8 m long with three elbows and one ball valve:

Branch sizeVelocityPressure drop (8 m)Share of 400 mbar
DN2535.4 m/s37.3 mbar9.3%
DN3219.4 m/s9.4 mbar2.3%
DN4011.5 m/s2.9 mbar0.7%

Branches should be DN32 or larger; long runs with more fittings go to DN40. Many sites step the branch down one size from the pump inlet to fit a flexible hose, and pay thirty-odd millibar at every station.

5. Run the 100 mbar section on its own main

A packaging chamber pulled to 100 mbar should not share a main with 400 mbar holding stations. That section uses DPL-LC250 (250 m³/h, ISO63 inlet, 2.2 kW) backed by DPL-V0100 (100 m³/h, 3.0 kW, G1¼″), a speed ratio of 2.5 with the backing pump working near 250 mbar, well inside the 0.1 mbar ultimate of the V0100. A 25 m DN65 main gives 25.4 m/s and 6.7 mbar, 6.7% of 100 mbar — too much; DN80 brings it to 16.1 m/s and 2.4 mbar. Pump data for the booster range is on the Roots vacuum pump page.

Sharing one main has a calculable cost: whenever the packaging chamber starts pumping, the whole main is pulled down and the six holding stations lose vacuum mid-transfer.

6. Buffer tank sizing

Tank volume comes from peak flow minus pump flow, multiplied by cycle time, divided by the permitted pressure swing. With a 200 m³/h pump (one DPL-V0202) and all eight stations moving for 4 s, the shortfall is 120 m³/h × 4 s = 0.133 m³ at 400 mbar, or 0.053 m³·bar.

TankPressure rise
1.0 m³53 mbar
1.5 m³36 mbar
2.0 m³27 mbar

Either a 1.5 m³ tank, or DPL-V0302 at 300 m³/h where the shortfall drops to 20 m³/h and a 1 m³ tank rises only 9 mbar. First pump-down of a 1 m³ tank from atmosphere to 400 mbar takes about 11 s with the V0302 and 17 s with the V0202, from t = (V / S) × ln(p₀ / p₁); the calculator handles the arithmetic.

7. Machine configurations

OptionPumpSpeed (50/60 Hz)PowerUltimateInletTank and mainWhere it fits
A decentralised8 × DPL-V0040A40 / 48 m³/h1.5 kW0.1 mbarG1¼″nonefew stations, no expansion planned
B single centralDPL-V0302300 / 360 m³/h7.5 kW0.1 mbarG2″1 m³ tank, DN80 mainthe 400 mbar section here
C duty/standby2 × DPL-V0202200 / 240 m³/h5.5 kW0.1 mbarG2″2 m³ tank, DN80 mainlines that cannot stop
D with boosterDPL-LC250 + DPL-V0100250 + 100 m³/h2.2 + 3.0 kWsee product pageISO63 / G1¼″DN80 main100 mbar section, higher flow
E oil-freeDPL-ZS150140 / 175 m³/h3.5 kW60 mbarG2″1 m³ tank, DN65 mainclean exhaust, stations above 100 mbar

Option A installs 12 kW against 7.5 kW for option B; the difference sits in machine count and simultaneity, not in pump efficiency. The ZS150 has an oil-free pumping chamber (0.85 L of oil in the gearbox only) and a 60 mbar ultimate, which limits it to stations at 100 mbar and above. Processes at the 10 mbar level need oil-sealed vane pumps or a Roots set; the comparison is on the central vacuum systems page, and packaged configurations are listed under packaged pump units.

Check supply frequency separately: 50 Hz and 60 Hz speeds differ — V0302 is 300 / 360 m³/h, ZS150 is 140 / 175 m³/h. The specification sheet notes that some models are not suited to 60 Hz regions; confirm motor and speed configuration with the factory before ordering, and recalculate main line and tank for the target frequency.

8. Six common mistakes

  1. Sizing pipe on atmospheric flow. 40 m³/h at 400 mbar is 15.8 m³/h at atmosphere; DN25 looks fine at 14 m/s atmospheric, but runs 35.4 m/s and loses 37 mbar at 400 mbar.
  2. Counting straight pipe only. Six elbows and two ball valves add about 9 m of equivalent length to a 30 m main, roughly a third more loss.
  3. Stepping the branch down from the pump inlet. A DN25 hose on a G2″ pump outlet costs thirty-odd millibar at every station.
  4. Mixing vacuum levels on one main. Packaging evacuation drags the holding stations down mid-transfer; split the mains and the machines.
  5. No check valve between tank and pump. Vacuum empties through the pump at standstill, and restart costs 11–17 s of pump-down.
  6. Ignoring leakage. Joints, valve packing and quick couplings all leak; after designing for 5% loss, pressure-test the line and check every joint.

Frequently asked questions

What pressure loss is acceptable in a central vacuum main?
Within 5% of working pressure. For a 400 mbar holding line, a 30 m DN65 main loses 30 mbar (7.5%) and is tight; DN80 loses 10.8 mbar (2.7%) and leaves 389 mbar at the far end.
Which flow should the main line be sized on?
The flow at the pump inlet. 300 m³/h at 400 mbar is only 118.5 m³/h at atmosphere; sized on that figure, DN50 runs 54.8 m/s and loses 115 mbar over 30 m.
How large should the buffer tank be for eight stations?
Size it on the peak shortfall. With a 200 m³/h pump and eight stations moving for 4 s, a 1 m³ tank rises 53 mbar and a 1.5 m³ tank rises 36 mbar; with DPL-V0302 at 300 m³/h a 1 m³ tank rises only 9 mbar.
Can holding stations and a packaging chamber share one main?
Not advisable. Split the 400 mbar and 100 mbar sections: DPL-V0302 with a 1 m³ tank for holding, DPL-LC250 backed by DPL-V0100 (ratio 2.5) for the 100 mbar chamber, each on its own DN80 main.
Can an oil-free dry pump serve this system?
For stations at 100 mbar and above, yes. DPL-ZS150 delivers 140 m³/h with a 60 mbar ultimate and oil-free exhaust; for 10 mbar level processes use oil-sealed vane pumps or a Roots set.

Need a model recommendation or a quote?

Tell us the required pumping speed, ultimate pressure, gas handled, dust and corrosion conditions, duty cycle and power supply; we will size the model for your process.

Contact us